---
title: User-Mode Commands
slug: ps/help/en_us/sd/25x/cli/user-mode-commands
docTags: 
createdAt: 2026-10-06T15:00:38.507Z
---

## Entering User-mode

:::Paragraph{indent="1"}
User-mode allows you to enter enable-mode, display system data, and perform standard networking tasks. Monitor users can perform user-mode commands. All commands available in user-mode are also available to administrator users.
:::

:::Paragraph{indent="1"}
To enter user-mode:
:::

- Connect to the CLI and enter the following command:

```bash
login as: admin
Brocade Services Director
Last login: Wed Jan 20 13:02:09 2010 from 10.0.1.1
amnesiac >
```

## User-Mode Commands

:::Paragraph{indent="1"}
The following section contains the Services Director commands.
:::

:::Paragraph{indent="1"}
For an alphabetical list of User-Mode commands, see the Table of Contents for this guide.
:::

### enable

:::Paragraph{indent="1"}
Enters enable mode.
:::

### Syntax

```bash
enable
```

### Usage Guidelines

:::Paragraph{indent="1"}
You must enter enable mode before you can perform standard network monitoring tasks.
:::

### Examples

```bash
amnesiac > enable
```

### exit

:::Paragraph{indent="1"}
Exits the CLI when in user mode; exits configuration mode when in configuration mode.
:::

### Syntax

```bash
exit
```

### Examples

```bash
amnesiac > exit
```

### ping

:::Paragraph{indent="1"}
Executes the ping utility to send ICMP ECHO\_REQUEST packets to network hosts using IPv4 addresses, for troubleshooting.
:::

### Syntax

```bash
ping [ options ]
```

### Parameters

```bash
options
```

:::Paragraph{indent="1"}
The **ping** command takes the standard Linux options. For detailed information, see the Linux manual (man) page.
:::

### Usage Guidelines

:::Paragraph{indent="1"}
The **ping** command without any options pings from the primary or the auxiliary (aux) interface and not the in-path interfaces.
:::

:::Paragraph{indent="1"}
If the primary and auxiliary interfaces are not on the same network as the in-path interfaces, you will not be able to ping an IP address on the in-path interface network unless you have a gateway between the two networks.
:::

:::Paragraph{indent="1"}
To ping from an in-path interface, use the following syntax:
:::

```bash
ping -I <in-path interface IP address> <destination IP address>
```

### Examples

```bash
amnesiac > ping -I 10.1.1.1 10.11.22.15
PING 10.11.22.15 (10.11.22.15) from 10.1.1.1: 56(84) bytes of data.
64 bytes from 10.11.22.15: icmp_seq=0 ttl=64 time=0.044 ms
64 bytes from 10.11.22.15: icmp_seq=1 ttl=64 time=0.038 ms
64 bytes from 10.11.22.15: icmp_seq=2 ttl=64 time=0.040 ms
```

### ping6

:::Paragraph{indent="1"}
Sends ICMP6\_ECHO\_REQUEST packets to a network host or gateway using IPv6 addresses, for troubleshooting.
:::

### Syntax

```bash
ping6 [ options ]
```

### Parameters

```bash
options
```

:::Paragraph{indent="1"}
The **ping6** command takes the standard Linux options. For detailed information, see the Linux manual (man) page.
:::

### Usage Guidelines

:::Paragraph{indent="1"}
The **ping6** command without any options pings from the primary or the auxiliary (aux) interface.
:::

### Examples

```bash
amnesiac > ping6 fe80::20e:b6ff:fe04:2788 fe80::20e:b6ff:fe02:b5b0
PING fe80::20e:b6ff:fe04:2788(fe80::20e:b6ff:fe04:2788) from fe80::20e:b6ff:fe02:b5b0 primary: 56 data bytes
64 bytes from fe80::20e:b6ff:fe04:2788: icmp_seq=0 ttl=64 time=1.14 ms
64 bytes from fe80::20e:b6ff:fe04:2788: icmp_seq=1 ttl=64 time=0.186 ms
--- fe80::20e:b6ff:fe04:2788 ping statistics ---
2 packets transmitted, 2 received, 0% packet loss, time 1001ms
rtt min/avg/max/mdev = 0.186/0.667/1.148/0.481 ms, pipe 2::0101:B3FF:FE1E:8937 2001:38dc:52::e9a4:c5:1001
```

### Related Commands

:::Paragraph{indent="1"}
[ipv6 in-path-gateway](docId:2rhKUtqx7Iti1A_X79KfL)
:::

### show access inbound rules

:::Paragraph{indent="1"}
Displays secure network access inbound configuration.
:::

### Syntax

```bash
show access inbound rules
```

### Examples

```bash
amnesiac > show access inbound rules
Secure network access enabled: no

Rule A Prot Service/ports Src network iface
----- - ---- ------------- ------------------ --------- -----------------------
A tcp 7800 0.0.0.0/0
A tcp 7801 0.0.0.0/0
A tcp 7810 0.0.0.0/0
A tcp 7820 0.0.0.0/0
A tcp 7850 0.0.0.0/0
A tcp ssh 10.0.24.7/32
1 A udp all 0.0.0.0/0 Allow DNS lookups
2 A udp 53 0.0.0.0/0 DNS Caching
```

### Related Commands

:::Paragraph{indent="1"}
[ssh client generate identity user](docId\:LLjz7el7U_q1thWAbTl0A)
:::

### show access status

:::Paragraph{indent="1"}
Displays secure network access status.
:::

### Syntax

```bash
show access status
```

### Examples

```bash
amnesiac > show access status
```

### Related Commands

:::Paragraph{indent="1"}
[ssh client generate identity user](docId\:LLjz7el7U_q1thWAbTl0A)
:::

### show alarm

:::Paragraph{indent="1"}
Displays the status of the specified alarm.
:::

### Syntax

```bash
show alarm type
```

### Parameters

```bash
type
```

:::Paragraph{indent="1"}
See [alarm enable](docId:2rhKUtqx7Iti1A_X79KfL) for a complete listing and description of alarm types.
:::

### Examples

```bash
amnesiac # show alarm warning_temp
Alarm Id: Warning Temperature
Alarm : The temperature of the appliance is above normal
Enabled: yes
Alarm State: ok
Error threshold: 70
Clear threshold: 67
Last error at: None
Last clear at: None
```

### Related Commands

:::Paragraph{indent="1"}
[alarm clear](docId:2rhKUtqx7Iti1A_X79KfL), [alarm enable](docId:2rhKUtqx7Iti1A_X79KfL), [show alarms](docId\:q-wP5fTzpWO2TO-RsyDPo)
:::

### show alarms

:::Paragraph{indent="1"}
Displays the status of all alarms.
:::

### Syntax

```bash
show alarms [ triggered ]
```

### Parameters

```bash
triggered
```

:::Paragraph{indent="1"}
Displays status and configuration of triggered alarms.
:::

### Examples

```bash
amnesiac > show alarms
Alarm Id: admission_conn
Alarm : Connection Limit Pressure
Status: ok
-----------------------------------------
Alarm Id: admission_control
Alarm : Admission Control Pressures
Status: ok
-----------------------------------------
Alarm Id: admission_cpu
Alarm : CPU Pressure
Status: ok
-----------------------------------------
Alarm Id: admission_mapi
Alarm : MAPI Pressure
Status: ok
-----------------------------------------
Alarm Id: admission_mem
Alarm : Memory Pressure
Status: ok
-----------------------------------------
Alarm Id: admission_tcp
Alarm : TCP Pressure
Status: ok
-----------------------------------------
Alarm Id: arcount
Alarm : Asymmetric Routing
Status: ok
-----------------------------------------
*** this is a partial listing ***
```

### Related Commands

:::Paragraph{indent="1"}
[alarm clear](docId:2rhKUtqx7Iti1A_X79KfL), [alarm enable](docId:2rhKUtqx7Iti1A_X79KfL), [show alarm](docId\:q-wP5fTzpWO2TO-RsyDPo)
:::

### show authentication policy

:::Paragraph{indent="1"}
Displays the status of the authentication policy.
:::

### Syntax

```bash
show authentication policy
```

### Examples

```bash
amnesiac > show authentication policy
Authentication policy enabled: yes
Maximum unsuccessful logins before account lockout: none
Wait before account unlock: 300 Seconds
Minimum password length: 6
Minimum upper case characters in password: 1
Minimum lower case characters in password: 1
Minimum numerical characters in password: 1
Minimum special characters in password: 1
Minimum interval for password reuse: 5
Minimum characters diff for password change: 4
Prevent dictionary words in password: yes
User passwords expire: 60 days
Warn user of an expiring password: 7 days before
User accounts with expired passwords lock: 305 days
```

### Related Commands

:::Paragraph{indent="1"}
[authentication policy enable](docId:2rhKUtqx7Iti1A_X79KfL)
:::

### show bootvar

:::Paragraph{indent="1"}
Displays the software image that is booted upon the next reboot.
:::

### Syntax

```bash
show bootvar
```

### Examples

```bash
amnesiac > show bootvar
Installed images:
Partition 1:
rbtsh/linux columbia #1 2004-02-07 19:24:24 root@test:repository
Partition 2:
rbtsh/linux Columbia #2 2004-02-13 17:30:17 root@test:repository
Last boot partition: 1
Next boot partition: 1
```

### Related Commands

:::Paragraph{indent="1"}
[host-label](docId:2rhKUtqx7Iti1A_X79KfL)
:::

### show cli

:::Paragraph{indent="1"}
Displays current CLI settings.
:::

### Syntax

```bash
show cli
```

### Examples

```bash
amnesiac > show cli
CLI current session settings
Maximum line size: 8192
Terminal width: 157 columns
Terminal length: 15 rows
Terminal type: xterm
Auto-logout: 30 minutes
Paging: enabled
CLI defaults for future sessions
Auto-logout: 30 minutes
Paging: enabled
```

### Related Commands

:::Paragraph{indent="1"}
[cli default paging enable](docId:2rhKUtqx7Iti1A_X79KfL)
:::

### show clock

:::Paragraph{indent="1"}
Displays current date and time.
:::

### Syntax

```bash
show clock [ all ]
```

### Parameters

```bash
all
```

:::Paragraph{indent="1"}
Displays the system time, date, and ntp peers.
:::

### Examples

```bash
amnesiac > show clock
Time: 15:11:13
Date: 2008/10/18
Zone: America North United_States Pacific
```

### show email

:::Paragraph{indent="1"}
Displays the current email settings.
:::

### Syntax

```bash
show email
```

### Examples

```bash
amnesiac > show email
Mail hub: exchange
Mail hub port: 30
Domain: example.com

Event emails
Enabled: yes
Recipients:
example@xxxxxxxx.com

Failure emails
Enabled: yes
Recipients:
example@xxxxxxxx.com

Autosupport emails
Enabled: no
Recipient:
sdauto@brocade.com
Mail hub:
eng.xxxxxxxx.com
```

### Related Commands

:::Paragraph{indent="1"}
[email autosupport enable](docId:2rhKUtqx7Iti1A_X79KfL)
:::

### show hardware error-log

:::Paragraph{indent="1"}
Displays IPMI system event log entries.
:::

### Syntax

```bash
show hardware error-log { all | new }
```

### Parameters

```bash
all
```

:::Paragraph{indent="1"}
Displays all IPMI SEL entries
:::

```bash
new
```

:::Paragraph{indent="1"}
Display IPMI SEL entries since the last **show hardware error-log** command was issued.
:::

```bash
licensing info
```

:::Paragraph{indent="1"}
Display current licenses.
:::

### Examples

```bash
amnesiac > show hardware error-log all
1 | 11/28/2006 11:55:10 | Event Logging Disabled SEL | Log area reset/cleared |
Asserted = yes.
2 | 01/04/2007 21:09:07 | Slot/Connector Drive | Fault Status | Asserted = yes.
3 | 01/07/2007 03:24:07 | Slot/Connector Drive | Fault Status | Asserted = yes.
```

### Related Commands

:::Paragraph{indent="1"}
[clear hardware error-log](docId\:qW4d1Kj33nMlkR3yej8BD)
:::

### show history

:::Paragraph{indent="1"}
Displays event history.
:::

### Syntax

```bash
show history [ category category ] [ severity level ]
```

### Parameters

```bash
category category
```

:::Paragraph{indent="1"}
Displays event history for the specified event category:
:::

:::Paragraph{listStyleType="disc" indent="2"}
alarm
:::

:::Paragraph{listStyleType="disc" indent="2"}
cli
:::

:::Paragraph{listStyleType="disc" indent="2"}
config
:::

:::Paragraph{listStyleType="disc" indent="2"}
mgmt
:::

:::Paragraph{listStyleType="disc" indent="2"}
web
:::

```bash

severity level
```

:::Paragraph{indent="1"}
Displays the minimum syslog severity threshold for the event category:
:::

:::Paragraph{listStyleType="disc" indent="2"}
emer: System unusable
:::

:::Paragraph{listStyleType="disc" indent="2"}
alert: Immediate action
:::

:::Paragraph{listStyleType="disc" indent="2"}
crit: Critical conditions
:::

:::Paragraph{listStyleType="disc" indent="2"}
err: Error conditions
:::

:::Paragraph{listStyleType="disc" indent="2"}
warning: Warning conditions
:::

:::Paragraph{listStyleType="disc" indent="2"}
notice: Normal but significant condition
:::

:::Paragraph{listStyleType="disc" indent="2"}
info: Informational messages
:::

:::Paragraph{listStyleType="disc" indent="2"}
debug: Debug-level messages
:::

### Usage Guidelines

:::Paragraph{indent="1"}
Alarms leave no record other than the message log, which is unstructured and not always helpful. Use the **show history** command to help diagnose problems by viewing the event history (an alarm is an example of an event). Other examples of events include a login or a configuration change. An event history displays all events at a glance, allows for the search description of alarms according to several criteria, and puts the alarms in the context of other time-based statistical information.
:::

### Examples

```bash
amnesiac > show history
Enable: yes
Last Ping: 2013-02-12 14:31:49.412973153 -0700
Saved Ping: 2013-03-21 07:25:51.000000000 -0700
```

### Related Commands

:::Paragraph{indent="1"}
[alarm enable](docId:2rhKUtqx7Iti1A_X79KfL)
:::

### show hardware watchdog

:::Paragraph{indent="1"}
Displays hardware watchdog information.
:::

### Syntax

```bash
show hardware watchdog
```

### Examples

```bash
amnesiac > show hardware watchdog
Enable: yes
Last Ping: 2006-05-12 14:31:49.412973153 -0700
Saved Ping: 2006-04-21 07:25:51.000000000 -0700
```

### Related Commands

:::Paragraph{indent="1"}
[host-label](docId:2rhKUtqx7Iti1A_X79KfL)
:::

### show hosts

:::Paragraph{indent="1"}
Displays system hosts.
:::

### Syntax

```bash
show hosts
```

### Examples

```bash
amnesiac > show hosts
Hostname: amnesiac
Name server: 10.0.0.2 (configured)
Domain name: domain.com (configured)
Domain name: domain.com (configured)
IP 107.0.0.1 maps to hostname localhost
```

### Related Commands

:::Paragraph{indent="1"}
[hostname](docId:2rhKUtqx7Iti1A_X79KfL)
:::

### show host-label

:::Paragraph{indent="1"}
Displays information about the specified host label.
:::

### Syntax

```bash
show host-label name [ detailed ]
```

### Parameters

```bash
name
```

:::Paragraph{indent="1"}
Specify the name of the host label.
:::

```bash
detailed
```

:::Paragraph{indent="1"}
Displays detailed hostname and subnet status information.
:::

### Examples

```bash
amnesiac # show host-label test
10.0.0.0/8, 192.168.0.1/32, 192.168.0.2/32, example.com, xxxxxxxx.com

amnesiac # show host-label test detailed

Subnets:
10.0.0.0/8, 192.168.0.1/32, 192.168.0.2/32

Host example.com:
192.0.43.10/32
Resolved: 2013/03/12 18:54:14

Host xxxxxxxx.com:
192.0.43.10/32
Resolved: 2013/03/12 18:54:14

Next scheduled resolve: 2013/03/13 18:54:09
```

### Related Commands

:::Paragraph{indent="1"}
[host-label](docId:2rhKUtqx7Iti1A_X79KfL)
:::

### show images

:::Paragraph{indent="1"}
Displays the available software images and which partition the appliance boots the next time the appliance is restarted.
:::

### Syntax

```bash
show images [ checksum ]
```

### Parameters

```bash
checksum
```

:::Paragraph{indent="1"}
Displays the Message-Digest 5 algorithm (MD5) checksum of the system images.
:::

### Examples

```bash
amnesiac > show images
Images available to be installed:
webimage.tbz
rbtsh/linux 4.0 #12 2007-05-15 11:54:52 root@test:CVS_TMS/HEAD
image.img
rbtsh/linux 4.0 #17 2007-05-22 16:39:32 root@test:CVS_TMS/HEAD
Installed images:
Partition 1:
rbtsh/linux 4.0-HEAD-2007-06-15-07:19:19 #0 2007-06-15 07:19:19 root@test:CVS_TMS/HEAD
Partition 2:
rbtsh/linux 4.0 2007-05-15 11:54:52 root@test:CVS_TMS/HEAD
Last boot partition: 2
Next boot partition: 2
```

### Related Commands

:::Paragraph{indent="1"}
[image install](docId\:qW4d1Kj33nMlkR3yej8BD)
:::

### show info

:::Paragraph{indent="1"}
Displays the system information, including the current state of the system.
:::

### Syntax

```bash
show info
```

### Examples

```bash
amnesiac > show info
Current User: admin
Status: Healthy
Config: initial
Appliance Up Time: 4h 4m 13s
Number of CPUs: 4
CPU load averages: 0.08 / 0.02 / 0.01
Temperature (C): 0
Serial: Unknown
Model: V1000
Revision: A
Version: 2.3.0-mainline
```

### Related Commands

:::Paragraph{indent="1"}
[configuration new](docId:2rhKUtqx7Iti1A_X79KfL)
:::

### show logging

:::Paragraph{indent="1"}
Displays logging and logging filter settings.
:::

### Syntax

```bash
show logging [ filter ]
```

### Parameters

```bash
filter
```

:::Paragraph{indent="1"}
Displays per-process logging configuration information.
:::

### Examples

```bash
amnesiac > show logging filter
Local logging level: info
amnesiac > show logging
Local logging level: info
Default remote logging level: notice
Remote syslog receiver: 10.10.10.2 (logging level: info)
Number of archived log files to keep: 10
Log rotation frequency: daily
```

### Related Commands

:::Paragraph{indent="1"}
[logging](docId:2rhKUtqx7Iti1A_X79KfL)
:::

### show ntp

:::Paragraph{indent="1"}
Displays NTP settings.
:::

### Syntax

```bash
show ntp [ all ]
```

### Parameters

```bash
all
```

:::Paragraph{indent="1"}
Display NTP settings and active peers.
:::

### Examples

```bash
amnesiac > show ntp
NTP enabled: yes

No NTP peers configured.

NTP servers:
0.vyatta.pool.ntp.org (version 4) Enabled: yes
1.vyatta.pool.ntp.org (version 4) Enabled: yes
2.vyatta.pool.ntp.org (version 4) Enabled: yes
3.vyatta.pool.ntp.org (version 4) Enabled: yes

No active ntp peers
```

### Related Commands

:::Paragraph{indent="1"}
[ntp server enable](docId\:Daj0PxouZD3s712K5TKUW)
:::

### show ntp active-peers

:::Paragraph{indent="1"}
Displays active NTP peers.
:::

### Syntax

```bash
show ntp active-peers
```

### Examples

```bash
amnesiac > show ntp active-peers
No active ntp peers
remote refid st t when poll reach delay offset jitter
==============================================================================
propjet.latt.ne .XFAC. 16 u - 1024 0 0.000 0.000 0.000
mail.coldnortha .XFAC. 16 u - 1024 0 0.000 0.000 0.000
services.quadra .XFAC. 16 u - 1024 0 0.000 0.000 0.000
yurizoku.tk .XFAC. 16 u - 1024 0 0.000 0.000 0.000

remote conf auth key
===================================
propjet.latt.ne yes none none
mail.coldnortha yes none none
services.quadra yes none none
yurizoku.tk yes none none
```

### Related Commands

:::Paragraph{indent="1"}
[ntp server enable](docId\:Daj0PxouZD3s712K5TKUW)
:::

### show ntp authentication

:::Paragraph{indent="1"}
Displays NTP authentication settings.
:::

### Syntax

```bash
show ntp authentication
```

### Examples

```bash
amnesiac > show ntp authentication
Trusted Keys: 5, 10

KeyID KeyType Encrypted Secret
-------------------------------------------------
5 MD5 rP1LTiIVk7QlMyFiLSpAKA==
65534 MD5 2Ovzk2RGghrBJLp6BX+BpSxo1pvz+5CM
```

### Related Commands

:::Paragraph{indent="1"}
[ntp server enable](docId\:Daj0PxouZD3s712K5TKUW)
:::

### show snmp

:::Paragraph{indent="1"}
Displays SNMP server settings.
:::

### Syntax

```bash
show snmp
```

### Examples

```bash
amnesiac > show snmp
SNMP enabled: yes
System location:
System contact:
Read-only community: public
Traps enabled: yes
No trap sinks configured.
```

### Related Commands

:::Paragraph{indent="1"}
[write memory](docId:2xtd8nOKdlgsAEu6GI3W6)
:::

### show snmp acl-info

:::Paragraph{indent="1"}
Displays SNMP access control list settings.
:::

### Syntax

```bash
show snmp acl-info
```

### Examples

```bash
amnesiac > show snmp acl-info
Security Names
--------------
Security name Community string Source address
------------- ---------------- --------------
There are no configured security names
Groups
------
Group name Security model Security name
---------- -------------- -------------
There are no configured groups
Views
-----
There are no configured views
Access control lists
---------------------
Group name Security level Read view
---------- -------------- -------------
```

### Related Commands

:::Paragraph{indent="1"}
[snmp-server enable](docId\:Daj0PxouZD3s712K5TKUW)
:::

### show snmp ifindex

:::Paragraph{indent="1"}
Displays the ifindex values for all interfaces.
:::

### Syntax

```bash
show snmp ifindex
```

### Examples

```bash
amnesiac > show snmp ifindex
Interface Ifindex
-----------------------
aux 1
eth0 6
eth1 7
eth2 8
eth3 9
eth4 10
eth5 11
eth6 12
eth7 13
lo 5
primary 2
```

### Related Commands

:::Paragraph{indent="1"}
[snmp-server enable](docId\:Daj0PxouZD3s712K5TKUW)
:::

### show snmp usernames

:::Paragraph{indent="1"}
Displays SNMP user settings.
:::

### Syntax

```bash
show snmp usernames
```

### Examples

```bash
amnesiac > show snmp usernames

Username Authentication Protocol Authentication Key
There are no configured users
```

### Related Commands

:::Paragraph{indent="1"}
[snmp-server enable](docId\:Daj0PxouZD3s712K5TKUW)
:::

### show ssh client

:::Paragraph{indent="1"}
Displays the client settings.
:::

### Syntax

```bash
show ssh client [ private ]
```

### Parameters

```bash
```

private

:::Paragraph{indent="1"}
Display SSH client public and private keys.
:::

### Examples

```bash
amnesiac > show ssh client
SSH server enabled: yes
```

### Related Commands

:::Paragraph{indent="1"}
[ssh client generate identity user](docId\:LLjz7el7U_q1thWAbTl0A)
:::

### show ssh server

:::Paragraph{indent="1"}
Displays the ssh server.
:::

### Syntax

```bash
show ssh server [ allowed-ciphers | publickey ]
```

### Parameters

```bash
allowed-ciphers
```

:::Paragraph{indent="1"}
Display SSH server allowed ciphers.
:::

```bash
publickey
```

:::Paragraph{indent="1"}
Display SSH server-public host key.
:::

### Examples

```bash
amnesiac > show ssh server publickey
SSH server public key: ssh-rsa AAAAB3NzaC1yc2XXXXXXXwAAAQEAwz7zKAc1NbTKSp40mRg7J
9YV5CeoGRQoCEPS17ValtEQbepaQygdifueiejht39837482y74982u7ridejbvgiIYZs/E23zmn212kj
dXFda8zJxJm07RIKOxNDEBUbAUp8h8dkeiejgfoeoriu39438598439gfjeNLfhjWgh1dzeGYycaAoEA
K21Igg+Sg0ELGq2cJ8mMzsSsCq5PnOmj63RAMuRgBdrtBdIAd32fy642PQJveqtfl7MBN6IwTDECRpex
F3Ku98pRefc2h0u44VZNT9h4tXCe8qHpuO5k98oA

amnesiac > show ssh server allowed-ciphers
SSH server allowed ciphers:
---------------------------
aes128-ctr
aes192-ctr
aes256-ctr
```

### Related Commands

:::Paragraph{indent="1"}
[ssh client generate identity user](docId\:LLjz7el7U_q1thWAbTl0A)
:::

### show stats cpu

:::Paragraph{indent="1"}
Displays CPU statistics.
:::

### Syntax

```bash
show stats cpu [ 1min | 5min | hour | day | week | month ]
```

### Parameters

```bash
1min | 5min | hour | day | week | month
```

:::Paragraph{indent="1"}
Specify a time interval to display CPU statistics.
:::

### Examples

```bash
amnesiac > show stats cpu
CPU 1
Utilization: 3%
Peak Utilization Last Hour: 10% at 2008/10/17 18:10:03
Avg. Utilization Last Hour: 4%
```

### Related Commands

:::Paragraph{indent="1"}
[show stats memory](docId\:q-wP5fTzpWO2TO-RsyDPo)
:::

### show stats ecc-ram

:::Paragraph{indent="1"}
Displays the ECC error counts.
:::

### Syntax

```bash
show stats ecc-ram
```

### Examples

```bash
amnesiac > show stats ecc-ram
No ECC memory errors have been detected
```

### Related Commands

:::Paragraph{indent="1"}
[show stats memory](docId\:q-wP5fTzpWO2TO-RsyDPo)
:::

### show stats fan

:::Paragraph{indent="1"}
Displays the fan statistics.
:::

### Syntax

```bash
show stats fan
```

### Examples

```bash
amnesiac > show stats fan
FanId RPM Min RPM Status
1 3825 750 ok
2 3750 750 ok
```

### Related Commands

:::Paragraph{indent="1"}
[show hardware error-log](docId\:q-wP5fTzpWO2TO-RsyDPo)
:::

### show stats memory

:::Paragraph{indent="1"}
Displays memory statistics.
:::

### Syntax

```bash
show stats memory [ 1min | 5min | hour | day | week | month ]
```

### Parameters

```bash
1min | 5min | hour | day | week | month
```

:::Paragraph{indent="1"}
Specify a time interval to display CPU statistics.
:::

### Examples

```bash
amnesiac > show stats memory
Total Swapped Over Last Hour: 0 pages
Average Swapped Over Last Hour: 0 pages
Peak Swapped Over Last Hour: 0 pages
Peak Swapped Time: 2008/10/17 17:37:41
```

### Related Commands

:::Paragraph{indent="1"}
[show stats ecc-ram](docId\:q-wP5fTzpWO2TO-RsyDPo)
:::

### show tcpdump stop-trigger

:::Paragraph{indent="1"}
Displays the configuration settings that trigger the stop of a TCP dump.
:::

### Syntax

```bash
show tcpdump stop-trigger
```

### Examples

```bash
amnesiac > show tcpdump stop-trigger
Tcpdump trigger enabled: no
Regex: ntp
Delay: 10
Last triggered on: 2013/01/12 17:33:52
Last triggered by: ntp
```

### Related Commands

:::Paragraph{indent="1"}
[tcpdump stop-trigger delay](docId:2xtd8nOKdlgsAEu6GI3W6), [tcpdump stop-trigger enable](docId:2xtd8nOKdlgsAEu6GI3W6), [tcpdump stop-trigger regex](docId:2xtd8nOKdlgsAEu6GI3W6), [tcpdump stop-trigger restart](docId:2xtd8nOKdlgsAEu6GI3W6)
:::

### show tcpdump-x

:::Paragraph{indent="1"}
Displays currently running tcpdumps.
:::

### Syntax

```bash
show tcpdump-x
```

### Examples

```bash
amnesiac > show tcpdump-x
No running capture
```

### Related Commands

:::Paragraph{indent="1"}
[tcpdump stop-trigger enable](docId:2xtd8nOKdlgsAEu6GI3W6)
:::

### show terminal

:::Paragraph{indent="1"}
Displays terminal settings.
:::

### Syntax

```bash
show terminal
```

### Examples

```bash
amnesiac > show terminal
CLI current session settings
Terminal width: 80 columns
Terminal length: 24 rows
Terminal type: xterm
```

### show uploads

:::Paragraph{indent="1"}
Displays system dump files uploaded to Technical Support.
:::

### Syntax

```bash
show uploads
```

### Usage Guidelines

:::Paragraph{indent="1"}
The **show uploads** command shows the system dump files that have been uploaded to Ivanti Technical Support or are in progress. The display shows up to 100 upload statistics, includes whether the upload is completed or in progress, and shows whether or not an error occurred during the upload process. You can clear the upload statistics using the **file upload clear-stats** command.
:::

### Examples

```bash
amnesiac > show uploads

Upload 0:
file: /var/opt/tms/tcpdumps/bravo-sh236_aux_new.cap0
url: ftp://ftp.xxxxxxxx.com/incoming/case_194170_F82JY00002BE4_bravo-sh236_aux_new.cap0
status: finished
percent complete: 100%
start time: 2013/03/25 12:16:40 -0700
finish time: 2013/03/25 12:16:41 -0700
```

### Related Commands

:::Paragraph{indent="1"}
[file upload clear-stats](docId\:qW4d1Kj33nMlkR3yej8BD)
:::

### show version

:::Paragraph{indent="1"}
Displays the installed software version, including build number.
:::

### Syntax

```bash
show version [ all | concise | history ]
```

### Parameters

```bash
all
```

:::Paragraph{indent="1"}
Displays version information for the current system image. This option displays the product release and the software version.
:::

```bash
concise
```

:::Paragraph{indent="1"}
Displays the installed software version without build information.
:::

```bash
history
```

:::Paragraph{indent="1"}
Displays upgrade version history.
:::

### Examples

```bash
amnesiac > show version
Product name: rbt_sh
Product release: 7.0.2
Build ID: #0
Build date: 2012-02-15 16:36:45
Build arch: x86_64
Built by: root@moscow.nbttech.com
Uptime: 15d 19h 40m 38s
Product model:
System memory: 208 MB used / 3681 MB free / 3890 MB total
Number of CPUs: 4
CPU load averages: 0.02 / 0.03 / 0.00

amnesiac > show version all
Product release: 1.0.1
RiOS release: rbt_sh 7.0.2 #202_101 2012-02-15 10:16:14 x86_64 root@basel:s
vn: //svn/mgmt/branches/release_branch
Build ID: #202_101
Build date: 2012-02-15 14:22:27
Build arch: x86_64
Built by: root@basel

Uptime: 14h 13m 5s

Product model: EX760
System memory: 5329 MB used / 10681 MB free / 16010 MB total
Number of CPUs: 4
CPU load averages: 0.36 / 0.40 / 0.32
```

### Related Commands

:::Paragraph{indent="1"}
[image fetch](docId\:qW4d1Kj33nMlkR3yej8BD), [image install](docId\:qW4d1Kj33nMlkR3yej8BD)
:::

### show web

:::Paragraph{indent="1"}
Displays current Web settings.
:::

### Syntax

```bash
show web
```

### Examples

```bash
amnesiac > show web
web-based management console enabled:
HTTP enabled: yes
HTTP port: 80
HTTPS enabled: yes
HTTPS port: 443
Inactivity timeout: 15 minutes
Session timeout: 60 minutes
Session renewal threshold: 30 minutes
```

### show web prefs

:::Paragraph{indent="1"}
Displays the current Web preferences.
:::

### Syntax

```bash
show web prefs
```

### Examples

```bash
amnesiac > show web prefs
Log:
Lines Per Page: 100
```

### show web ssl cert

:::Paragraph{indent="1"}
Displays certificate details.
:::

### Syntax

```bash
show web ssl cert
```

### Examples

```bash
amnesiac > show web ssl cert
Issued To:
Common Name: gen-sh226
Email: admin@gen-sh226
Organization: Brocade
Organization Unit:
Locality: San Francisco
State: California
Country: --
Issued By:
Common Name: gen-sh226
Email: admin@gen-sh226
Organization: Brocade
Organization Unit:
Locality: San Francisco
State: California
Country: --
Validity:
Issued On: May 4 22:18:55 2011 GMT
Expires On: May 3 22:18:55 2012 GMT
Fingerprint:
SHA1:
```

### slogin

:::Paragraph{indent="1"}
Enables log in to another system securely using SSH.
:::

### Syntax

```bash
slogin [ options ]
```

### Parameters

```bash
options
```

:::Paragraph{indent="1"}
Specify slogin options. To view options, enter slogin at the system prompt.
:::

### Examples

```bash
amnesiac > slogin -l usertest
```

### Related Commands

:::Paragraph{indent="1"}
[show ssh client](docId\:q-wP5fTzpWO2TO-RsyDPo), [show ssh server](docId\:q-wP5fTzpWO2TO-RsyDPo)
:::

### stats export

:::Paragraph{indent="1"}
Enables the export of statistics.
:::

### Syntax

```bash
stats export csv report-name after yyyy/ mm/ dd before yyyy/ mm/ dd email email-addr filename filename
```

### Parameters

```bash
csv
```

:::Paragraph{indent="1"}
Specify the file format for export: csv
:::

```bash
report-name
```

:::Paragraph{indent="1"}
Specify one of the following reports:
:::

:::Paragraph{listStyleType="disc" indent="2"}
cpu\_util: CPU utilization
:::

:::Paragraph{listStyleType="disc" indent="2"}
memory: Memory utilization
:::

:::Paragraph{listStyleType="disc" indent="2"}
paging: Paging I/O
:::

:::Paragraph{listStyleType="disc" indent="2"}
appvissummary: Application visibility summary report
:::

:::Paragraph{listStyleType="disc" indent="2"}
appvishistory: Application visibility history report
:::

:::Paragraph{listStyleType="disc" indent="2"}
bw: Aggregate bandwidth
:::

:::Paragraph{listStyleType="disc" indent="2"}
th\_peak: Peak throughput
:::

:::Paragraph{listStyleType="disc" indent="2"}
th\_p95: P95 throughput
:::

:::Paragraph{listStyleType="disc" indent="2"}
pass: Aggregate pass-through traffic
:::

:::Paragraph{listStyleType="disc" indent="2"}
cpool: Aggregate connection pooling
:::

:::Paragraph{listStyleType="disc" indent="2"}
nfs: Aggregate NFS report
:::

:::Paragraph{listStyleType="disc" indent="2"}
pfs: Aggregate PFS report
:::

:::Paragraph{listStyleType="disc" indent="2"}
conn\_history: connection history
:::

:::Paragraph{listStyleType="disc" indent="2"}
dstore: Data store hit
:::

:::Paragraph{listStyleType="disc" indent="2"}
ssl: SSL statistics
:::

:::Paragraph{listStyleType="disc" indent="2"}
ssl\_peak: SSL peak statistics
:::

:::Paragraph{listStyleType="disc" indent="2"}
http: HTTP statistics
:::

:::Paragraph{listStyleType="disc" indent="2"}
qos: QoS statistics
:::

:::Paragraph{listStyleType="disc" indent="2"}
qos\_inbound: Inbound QoS statistics
:::

:::Paragraph{listStyleType="disc" indent="2"}
snapmirror: Snapmirror statistics
:::

:::Paragraph{listStyleType="disc" indent="2"}
snapmirror\_peak: Snapmirror peak statistics
:::

:::Paragraph{listStyleType="disc" indent="2"}
topconversations: Top conversations report
:::

:::Paragraph{listStyleType="disc" indent="2"}
topsenders: Top senders report
:::

:::Paragraph{listStyleType="disc" indent="2"}
topreceivers: Top receivers report
:::

:::Paragraph{listStyleType="disc" indent="2"}
topapplications: Top applications report
:::

```bash
after yyyy / mm/ dd
```

:::Paragraph{indent="1"}
Includes statistics collected after a specific time.
:::

```bash
before yyyy/ mm/ dd
```

:::Paragraph{indent="1"}
Includes statistics collected before a specific time.
:::

```bash
email email-addr
```

:::Paragraph{indent="1"}
Specify the address where the report is to be emailed.
:::

```bash
filename filename
```

:::Paragraph{indent="1"}
Specify a filename for the new report.
:::

### Examples

```bash
amnesiac > stats export csv ssl after 2008/09/01 filename ssltest
```

### Related Commands

:::Paragraph{indent="1"}
[show stats cpu](docId\:q-wP5fTzpWO2TO-RsyDPo)
:::

### support show disk

:::Paragraph{indent="1"}
Displays disk statistics for the drive containing the Services Director.
:::

### Syntax

```bash
support show disk
```

### Examples

```bash
amnesiac > support show disk
Filesystem 1K-blocks Used Available Use% Mounted on
rootfs 2071416 1102520 863672 57% /
udev 4053260 160 4053100 1% /dev
tmpfs 4062768 0 4062768 0% /dev/shm
/dev/sda5 2071416 1102520 863672 57% /
tmpfs 1048576 9576 1039000 1% /lib/modules
tmpfs 1048576 6348 1042228 1% /lib/firmware
none 16384 164 16220 2% /tmp
/dev/sda2 132221 67116 58278 54% /boot
/dev/sda1 256665 8504 234908 4% /bootmgr
/dev/sda8 16516084 1496416 14180676 10% /var
/dev/sda9 1035692 33824 949256 4% /config
/dev/sda10 8262068 319380 7522992 5% /data
none 4062768 0 4062768 0% /dev/shm
encfs 16516084 1496416 14180676 10% /var/opt/rbt/decrypted
```

### Related Commands

:::Paragraph{indent="1"}
[show stats memory](docId\:q-wP5fTzpWO2TO-RsyDPo)
:::

### terminal

:::Paragraph{indent="1"}
Sets terminal settings.
:::

### Syntax

```bash
terminal { length lines | type terminal_type | terminal width number-of-characters }
```

### Parameters

```bash
[no] terminal length lines
```

:::Paragraph{indent="1"}
Sets the number of lines 0-1024; 0 to disable paging.
:::

:::Paragraph{indent="1"}
The **no** command option disables the terminal length.
:::

```bash
[no] terminal type terminal_type
```

:::Paragraph{indent="1"}
Sets the terminal type.
:::

The **no** command option disables the terminal type.

```bash
[no] terminal width number-of-characters
```

:::Paragraph{indent="1"}
Sets the width number of characters.
:::

:::Paragraph{indent="1"}
The **no** command option disables the terminal width.
:::

### Usage Guidelines

:::Paragraph{indent="1"}
The **no** command option disables terminal settings.
:::

### Examples

```bash
amnesiac > terminal width 1024
```

### Related Commands

:::Paragraph{indent="1"}
[ssh client generate identity user](docId\:LLjz7el7U_q1thWAbTl0A)
:::

### traceroute

:::Paragraph{indent="1"}
Executes the traceroute utility for IPv4 addresses. The traceroute command takes the standard Linux options.
:::

### Syntax

```bash
traceroute [ options ]
```

### Parameters

```bash
options
```

:::Paragraph{indent="1"}
The traceroute command takes the standard Linux options. For detailed information, see the Linux manual (man) page.
:::

### Examples

```bash
amnesiac > traceroute amnesiac
traceroute to amnesiac.domain.com (10.0.0.3), 30 hops max, 38 byte packets
1 amnesiac (10.0.0.3) 0.035 ms 0.021 ms 0.013 ms
```

### traceroute6

:::Paragraph{indent="1"}
Executes the traceroute utility for IPv6 addresses. The traceroute6 command takes the standard Linux options.
:::

### Syntax

```bash
traceroute6 [ options ]
```

### Parameters

```bash
options
```

:::Paragraph{indent="1"}
The traceroute6 command takes the standard Linux options. For detailed information, see the Linux manual (man) page.
:::

### Examples

```bash
amnesiac > traceroute6 amnesiac
traceroute6 to amnesiac.domain.com (2001:38dc:52::e9a4:c5:6282/64), 30 hops max, 38 byte packets
1 amnesiac (2001:38dc:52::e9a4:c5:6282/64) 0.035 ms 0.021 ms 0.013 ms
```

### Related Commands

:::Paragraph{indent="1"}
[ipv6 in-path-gateway](docId:2rhKUtqx7Iti1A_X79KfL)
:::