---
title: Example Configuration: Guest Access with Juniper Mist WLC
slug: example-configuration-guest-access-with-juniper-mist-wlc
createdAt: 2026-07-27T04:11:11.780Z
---

This section describes the configuration that is required on IPS to communicate with Juniper Mist WLC for Guest wireless authentication.

To configure IPS for guest wireless authentication:

1. Select **Authentication > Auth.Servers**. The Authentication Servers screen appears. Use the Default Guest Wired Authentication Server.:inlineImage[]{src="https://api.archbee.com/api/optimize/wxZG1KsS4xNkVZYoiu_o9/atuP5Sp-IcOrg1QpUWjO7_authenticationserverscreen.png" alt caption size="61" width="607" height="189"}
2. Click Guest Wired Authentication available by default to view the settings.:inlineImage[]{src="https://api.archbee.com/api/optimize/wxZG1KsS4xNkVZYoiu_o9/NWW4QOSWZlORrZlpnt0uC_macaddressmist.png" alt caption size="61" width="607" height="467"}
3. You can make the necessary changes and click **Save Changes**.
4. Select Users > User Roles. The User Roles page appears.:inlineImage[]{src="https://api.archbee.com/api/optimize/wxZG1KsS4xNkVZYoiu_o9/ytsRqKQ6MJeqzT0IOnhJu_role1.png" alt caption size="61" width="607" height="244"}
5. Click Guest Wired Restricted user role available by default. The Agentless access is enabled for this role.
6. Select **Endpoint Policy > MAC Address Authentication Realms&#x20;**&#x61;nd click Guest Wired authentication realm available by default.:inlineImage[]{src="https://api.archbee.com/api/optimize/wxZG1KsS4xNkVZYoiu_o9/C1CoSsfhJnK1qhDLuCF7i_endpointpolicymacauthrealm.png" alt caption size="63" width="628" height="498"}
7. Select **Endpoint Policy > Network Access > Location Group**. Select Guest Wired as MAC Auth Realm.
8. Configure the Mist WLC as a RADIUS client. Ensure that the Guest Wired location group and Support Disconnect Messages options are enabled.

::Image[]{src="https://api.archbee.com/api/optimize/wxZG1KsS4xNkVZYoiu_o9/11rE_9Q5AnsegZUFYkST4_configuremistwlcasradiusclient.png" position="flex-start" size="62" width="616" height="292" initialPath="images/configure_mist_wlc_as_radius_client.png" githubPath="images/configure_mist_wlc_as_radius_client.png" showCaption="false"}

Configure the RADIUS return attributes for Guest Wired policy. Select **Endpoint Policy > Network Access > RADIUS Return Attribute Policies**. Click **New** **Policy**. Under RADIUS Attributes tab, select the check box for **Return** **Attribute**.The RADIUS return attributes are required for MAB authentication initially when the guest connects to the SSID (where the redirection happens) and then the session is bridged after the guest authenticates.
Supported Attributes: Filter-Id, Airspace-ACL-Name, Aruba-User-Role.
Cisco-AVPair is supported to set the redirection URL.
Tunnel-Private-Group-ID and Airespace-Interface-Name are used to assign the VLANS.

::Image[]{src="https://api.archbee.com/api/optimize/wxZG1KsS4xNkVZYoiu_o9/J06EnnV4wGxcZg-_TRZWd_configureradiusreturnattributes.png" position="flex-start" size="60" width="595" height="233" initialPath="images/configure_radius_return_attributes.png" githubPath="images/configure_radius_return_attributes.png" showCaption="false"}

### Configuring Mist WLC

To configure WLAN on Mist:

1. Add Mist as Access Point.

::Image[]{src="https://api.archbee.com/api/optimize/wxZG1KsS4xNkVZYoiu_o9/mjme-ue_Xfw-ymNO_Pplb_addmistasaccesspoint.png" position="flex-start" size="64" width="638" height="206" initialPath="images/add_mist_as_access_point.png" githubPath="images/add_mist_as_access_point.png" showCaption="false"}

Setup the Wireless Networks, Select **Network > WLANs**. Click **Add WLAN**.

3. Configure Name, SSID.
4. Under Security, select **Open Access**.
5. Enable **Guest Access with Mac Authentication Bypass**.
6. Under RADIUS Authentication Server and RADIUS Accounting Server, specify the IPS IP address.:inlineImage[]{src="https://api.archbee.com/api/optimize/wxZG1KsS4xNkVZYoiu_o9/Fz6BFAuvOUobaVrCj65NL_specifyipsipforradiusauthaccserver.png" alt caption size="62" width="620" height="1056"}
7. Create Security Policy to control resource access.:inlineImage[]{src="https://api.archbee.com/api/optimize/wxZG1KsS4xNkVZYoiu_o9/QPSesZOs4zQidWP8HUWKO_createsecuritypolicytocontrolaccess.png" alt caption size="62" width="618" height="215"}
8. You can also issue a label. The label is used to form tags or groups, which can be used to create security policies.:inlineImage[]{src="https://api.archbee.com/api/optimize/wxZG1KsS4xNkVZYoiu_o9/xXyFNL1cYXfHPRAnMe93s_label.png" alt caption size="80" width="1840" height="852"}
